Hello everyone. Got a couple of repairs scheduled for spring. The one I need some advice on is a leak in the holding tank. Anyone ever fix a plastic tank with some kind of exotic glue or maybe plastic weld. It might be better to replace the tank but I thought that might be a little pricey and a lot more work.

Views: 138

Reply to This

Replies to This Discussion

i used fiberglass but sometimes it`s better to just replace because it does twist and can crack

oh and one time i took a tourch and found a good size piece and kind of plastic wielded it on low temp and kept smashing it until it was all smeared it worked



    Just a thought.  Harbor Freight make a plastic welder.  It has mixed reviews but may work for you.  Also You Tube has been helpful in the past for finding ways to do things.  H/F link  http://www.harborfreight.com/plastic-welding-kit-with-adjustable-te...  Hope this helps, Tony, Joy and Cool Paw Luke

Thanks dude. Copied it to my computer. Even if I don't use it now handy for the future.

I bought a Harbor Freight plastic welder to repair my two holding tanks.  There appeared to be a steep learning curve in using the welder, but I was eventually able to fix both tanks except for a leak at the top.  I didn't remove the tanks and the top leak is a not so subtle reminder to dump the tank!  My tanks are a whitish plastic that seemed to accept a weld with plastic from common milk bottles.  I can only say, go slow, don't heat it up too much to the point were it burns.  Also, my tanks are only supported at the ends and are subject to varying stresses as the tank fills; I also bought some cargo straps at HF and installed two on each tank at approximately 1/3 locations.  My tanks are 35 years old and still working adequately. Good Luck with your projects, and let us know how they turn out.

Thanks for the response. Be at least 3 more months before I can tackle this job. Way too cold outside in northern ontario.

I have made repairs before on plastic with sheet pvc and the glue plumbers use for pvc pipe .First measure the area to be repaired then cut an oversize piece of PVC sheet that is about 1/4 inch thick. Clean and lightly sand the area to be repaired wipe with acetone let dry a few minutes then apply the PVC glue primer (It is usually purple) let that dry a few minutes then coat the repair patch and the tank with PVC general purpose glue and put the patch over the bad spot. Hold in place for a few minutes and then allow the repair to dry for at least a day. I found that General purpose PVC glue works on a variety of plastic compounds. I have even laminated sheets of PVC together to make electrical boxes for motorcycles-etc.

Didn't know they made sheet pvc. Thought it was only pipe. Got nothing to loose by trying one of these ideas before spending $400 and a lot of time to change the tank.

Yep you can order some online I happened to find mine from an old store display. PVC actually chemically welds itself together  ever try pulling PVC pipe apart?




  •         How To Links 

-Search Good Old RV's

-Start a New Group 

-Roof Repair Photos & Products

-Repair an RV Roof

-Pick Roof Sealer   

-Understanding RV Electrical Systems 

-Get RV Insurance   

-What to Look For When Buying a Used RV

-Jack Installs Fuel Injection in his Dodge 


 Paige's VintageTrailer Art  

 Paige's VintageTrailerFabric

 Artist Roads                                            Sandy's Stained Glasshttps://www.pinterest.com/pin/552605816752050167/     



If you love classic and vintage RVs then come Join us. Come on in and have some fun. JOIN HERE NOW


Engine removal 1 Reply

Started by Montana Bob in RV Repair & Maintence. Last reply by Daniel Long Jan 7.

top speed of a 83 shasta class c 3 Replies

Started by Billy lotz in RV Repair & Maintence. Last reply by Davd Farrell Jan 5.

93 pace arrow diesel 2 Replies

Started by Davd Farrell in RV Repair & Maintence. Last reply by Davd Farrell Jan 4.

Blog Posts

1983 Apollo 3300 DB

Posted by Bradley on December 8, 2019 at 8:58am — 2 Comments

California PSPS and fires

Posted by Steve Kaiser on November 2, 2019 at 6:53pm

1962 Fireball Meteor 16’ w/title

Posted by Chris on October 29, 2019 at 3:00pm

FOR SALE 1973 Chinook 2500 ($15,000 OBO)

Posted by Stephen Datnoff on September 23, 2019 at 11:29pm

just so you know our rig.

Posted by Dave Haslam on September 22, 2019 at 6:03pm


  • Add Videos
  • View All


If you love classic and vintage RVs then come Join us.

 Come on in and have some fun.         JOIN HERE NOW!

 Dedicated to a simpler, more rewarding and fun way of life in a Good Old RV... 

Vintage Travel Trailers, Vintage Campers, Camper Restoration, Bus Conversions, Vintage RV Forums, Old RVs, Tiny Homes, Boondocking


A work of art by member Paige Bridges

Get your Good Old RVs T-Shirt HERE


 Disclaimer - Please Read it

Enjoy this site and use it totally at your own risk.

By using or viewing this site YOU agree to Hold Harmless anyone associated with it including other members. Also, YOU agree that YOU are solely responsible for ANY and ALL actions, results or damages. Members "opinions" are just that and any repair or alteration comments or recommendations are by folks who are not licensed repair  or mechanical professionals. Any repairs or modifications you do totally at YOUR OWN RISK. Use licensed professionals for all work to avoid possible serious injury or damage. Use  banks for purchases.  Have fun!

Copywrite & Trade Mark Registered GoodOldRV© ,GoodOldRVs©, GoodOldRVs.com©,GoodOldRVs.net©,GoodOldRV.Com©

© 2020   Created by Russell E Johnson.   Powered by

Badges  |  Report an Issue  |  Terms of Service