Twist on the Roof Sealant Question - Good Old RVs2024-03-28T22:40:23Zhttps://goodoldrvs.ning.com/forum/topics/twist-on-the-roof-sealant-question?commentId=2093474%3AComment%3A244203&feed=yes&xn_auth=noThanks all for the replies. I…tag:goodoldrvs.ning.com,2015-01-20:2093474:Comment:2443722015-01-20T22:23:49.692ZJim Stoltzhttps://goodoldrvs.ning.com/profile/JimStoltz
<p>Thanks all for the replies. I think David is right - no matter what I use for sealant, it's futile if those mounts are loose. And some of them are. I've already applied copious amounts of Liquid roof to each and every mount. There are two that are suspect near the fridge vent - they're really loose. I guess I need to finish the job of securing it with bigger mounting screws. Then I'll use Eternabond or Dicor tape over it. I don't want to remove it at this point because the mounting points…</p>
<p>Thanks all for the replies. I think David is right - no matter what I use for sealant, it's futile if those mounts are loose. And some of them are. I've already applied copious amounts of Liquid roof to each and every mount. There are two that are suspect near the fridge vent - they're really loose. I guess I need to finish the job of securing it with bigger mounting screws. Then I'll use Eternabond or Dicor tape over it. I don't want to remove it at this point because the mounting points that I did secure are holding well.</p>
<p></p>
<p>I have the heat cranked up to try to dry it out. Might be a good opportunity to hack the carpet out and get going on the Allure tile installation.....</p> I like riches approach. The d…tag:goodoldrvs.ning.com,2015-01-20:2093474:Comment:2444352015-01-20T03:35:15.373Zdavid crafthttps://goodoldrvs.ning.com/profile/davidcraft
I like riches approach. The dicor self leveling or the non-sag is 100% compatible with the liquid roof. I thought I already posted on this..hehe. Unless the mounts are 100% secure though, it is an exercise in futility. Bigger bolts if rigid. A plate piece of metal larger in area than rack mount to gain fresh material to mount to. If you cant get a good mount, pull rack and eterna bond mount locations or something.
I like riches approach. The dicor self leveling or the non-sag is 100% compatible with the liquid roof. I thought I already posted on this..hehe. Unless the mounts are 100% secure though, it is an exercise in futility. Bigger bolts if rigid. A plate piece of metal larger in area than rack mount to gain fresh material to mount to. If you cant get a good mount, pull rack and eterna bond mount locations or something. When I done my roof Jim, I re…tag:goodoldrvs.ning.com,2015-01-20:2093474:Comment:2444322015-01-20T02:45:43.381ZRich Thomashttps://goodoldrvs.ning.com/profile/RichThomas
<p>When I done my roof Jim, I removed the screws and cleaned under the mounts and the mount areas off with acetone then replaced butyl tape under all the mounts and reattached. After that I used self leveling Dicor over the top. It has worked well so far. I had it in the back of my mind that if I have to do it again i'll use some type of epoxy between the mounts and roof to keep them from vibrating loose over time. I think Eternabond would work better than the butyl tape as well but, I was done…</p>
<p>When I done my roof Jim, I removed the screws and cleaned under the mounts and the mount areas off with acetone then replaced butyl tape under all the mounts and reattached. After that I used self leveling Dicor over the top. It has worked well so far. I had it in the back of my mind that if I have to do it again i'll use some type of epoxy between the mounts and roof to keep them from vibrating loose over time. I think Eternabond would work better than the butyl tape as well but, I was done with the job before I learned about it. I just hate it when a repair fails and hope you find a good solution for your situation.</p> Take the screws out put a sea…tag:goodoldrvs.ning.com,2015-01-20:2093474:Comment:2441172015-01-20T01:14:24.479ZJames and Yvonne Hoakhttps://goodoldrvs.ning.com/profile/Jameshoak
Take the screws out put a sealant in the screw hole and screw it back in each hole once the sealant drys coat the screws with the roof sealant that's what I Did on mine and it has worked just fine.
Take the screws out put a sealant in the screw hole and screw it back in each hole once the sealant drys coat the screws with the roof sealant that's what I Did on mine and it has worked just fine. To be clear - water is enteri…tag:goodoldrvs.ning.com,2015-01-19:2093474:Comment:2442032015-01-19T18:51:15.844ZJim Stoltzhttps://goodoldrvs.ning.com/profile/JimStoltz
<p>To be clear - water is entering the fridge vent after finding its way from the luggage rack mounts to the vent. It's not the vent itself.</p>
<p>To be clear - water is entering the fridge vent after finding its way from the luggage rack mounts to the vent. It's not the vent itself.</p>