Alright time for my next stupid question. I am going to replace all the clearance lights on the Aluma-lite with Led lights. Can I use plumbers putty around the base of the lights like you do around the flange of a sink drain to make it waterproof? I can not find a local source of butyl tape and the putty seems to be about the same thing.

Views: 183

Reply to This

Replies to This Discussion

That Plumbers putty is a good back up when butyl tape isnt available,, I have used it,, and I doubted it at first, but it actually turned out to be pretty much the same thing.You shouldnt have any problems using the plumber putty.

Butyl tape should be available from any residential glass shop. Grey or black, 1/8 x 3/8 & 1/16 x 3/8.

If you are in a hurry your local hardware store shout have.

OK, Next problem with clearance lights, when they built this monster they bored a huge hole (About 1 inch) to run wires thru and riveted the clearance lights on. After drilling out the rivet I found they used a 1/4 inch hole BIG RIVETS.  I thought I could just use my handy hand riveter and no the RV Gods frowned upon me and there is not enough room between the circuit board of the new lights and the casing to get my riveter in. Went to Homehell and bought some anchors but they are not working either. With a 1/4 inch hole you can't get the last 1/4 inch of the anchor flush and if you enlarge the hole a smidgen the the plastic anchor just spins. What do I do now??? 

I have used *Fender Clips,, (auto parts stores)   They are a  *U shaped clip that a screw attaches to,, They ahve different sizes But I have used the small with excellent results,,, and NO drilling, The U clip *fender clip slides over the holes,, covering the front and back and you ya put in the ole screw and your all set,,

Hers an example, of what they look like,

thanks I tried that but the distance from the center hole to the mounting holes is too great.

Threaded inserts maybe a little pricey.  I have had good luck when nothing else does the job.

might give that some thought, wondering where I can find them local since I need the RV this weekend.

Hi john, if you are close to a Lowe's or other big box hardware store like Home Depot; take a little time and explore the fastener isle. There you will find a large assortment of specialty fasteners used by furniture makers like the sawdust junk you can buy from Walmart. There just may be something that will fill the bill for your project. at any rate good luck on your project.

Well finally got the lights switched out. Had to move all of them up a bit and used sheet metal screws. Almost ready to take to Fla. this weekend and shoot Yankee's.


Here is a shot of the rear.


Looks fantastic!  Glad you found a workable solution, and thanks for posting what you did.




  •         How To Links 

-Search Good Old RV's

-Start a New Group 

-Roof Repair Photos & Products

-Repair an RV Roof

-Pick Roof Sealer   

-Understanding RV Electrical Systems 

-Get RV Insurance   

-What to Look For When Buying a Used RV

-Jack Installs Fuel Injection in his Dodge 



 Artist Roads                                              



If you love classic and vintage RVs then come Join us. Come on in and have some fun. JOIN HERE NOW

Blog Posts

Not OLD enough

Posted by jim bornemann on November 29, 2021 at 8:17pm


Posted by matt zodrow on October 25, 2021 at 10:05am

JAMEE ll owners manual needed- 1981 or 1982 or 1983

Posted by Don Novak on October 9, 2021 at 10:50pm — 1 Comment

Anyone got a manual for my camper ?

Posted by Pacy on September 21, 2021 at 10:17am

Anyone know what year this Corsair could be.

Posted by Jay M Ball on August 22, 2021 at 6:24pm — 1 Comment


  • Add Videos
  • View All


If you love classic and vintage RVs then come Join us.

 Come on in and have some fun.      

 Dedicated to a simpler, more rewarding and fun way of life in a Good Old RV... 

Vintage Travel Trailers, Vintage Campers, Camper Restoration, Bus Conversions, Vintage RV Forums, Old RVs, Tiny Homes, Boondocking

A work of art by member Paige Bridges


 Disclaimer - Please Read it

Enjoy this site and use it totally at your own risk.

By using or viewing this site YOU agree to Hold Harmless anyone associated with it including other members. Also, YOU agree that YOU are solely responsible for ANY and ALL actions, results or damages. Members "opinions" are just that and any repair or alteration comments or recommendations are by folks who are not licensed repair  or mechanical professionals. Any repairs or modifications you do totally at YOUR OWN RISK. Use licensed professionals for all work to avoid possible serious injury or damage. Use  banks for purchases.  Have fun!

Copywrite & Trade Mark Registered GoodOldRV© ,GoodOldRVs©,©,©,GoodOldRV.Com©

© 2021   Created by Russell E Johnson.   Powered by

Badges  |  Report an Issue  |  Terms of Service