Comment
I don't know which distributor I have in it: stock or the one that came with the new engine. It seems to run okay though. I have an advance timing gun so I can check it.
I'm at the mercy of my stock distributor for timing. I do have an advance timing gun so I'll check it out. So far it runs great and doesn't knock, but I'd like the peace of mind of knowing where the timing is off-idle.
Thanks Jack. I set the timing to factory specs when I first installed the engine but I had it hooked up to the "wrong" port ("wrong" depends on your objective - from what I've read hooking it up to a full vacuum port won't hurt anything but will affect emissions).
I leaned it out a bit with the idle air screws. Idle picked up a bit so I turned it back.
I was goofing around with the carb today and realized that I had the vacuum advance hooked up to a constant vacuum source rather than ported so the timing was always advanced 30 degrees. Apparently this affects emissions, primarily HCs. I hooked it up the right way and adjusted the idle back up to 850-900. I took it for a spin and the change doesn't seem to have affected anything off-idle.
The brakes are acting funny again though. I think I'm losing my power assist. The pedal gets stiff but the brakes seem to work okay - just requires more effort. If I shut the engine off and turn it back on it seems okay again.
Thanks Jack. It's an idle test. I took the air pump off of it when I put the new engine in. My GM Tech friend says it should pass easily without it. What you describe is what I've learned is an "idle drop tune", which my friend says should get me through. The issue was that before I had it rebuilt, turning the idle air screws in all the way had no affect on the idle. I had either an air or fuel leak I guess. I haven't messed with this one yet, but I assume that I should be able to stall it if I close the screws completely.
It doesn't have a cat from the factory. I'm not sure a cat would do it anyway. I haven't messed with the idle screws since I got it back from the rebuilder. I contacted a GM tech friend of mine and he said the numbers are close enough that I should be able to lean it out enough to get through. Worst case is I'll have to take it to his shop for inspection, but I really just wind up paying his boss not him directly so I haven't gone that route yet.
According to people on the 'Net, watching the vacuum while you adjust the idle screws is important to get it optimally tuned. I ordered a vacuum gauge from eBay (yeah, I could probably find one locally but I don't have time to mess with it until the weekend anyway).
On a side note, I had the on-board propane tank refilled yesterday. The gas station attendant (NJ can't pump your own gas) thought he was capable. I could tell by the way he was fumbling with it that there was going to be trouble. As soon as he flipped the pump on there was liquid propane everywhere, coming out of the fitting he put on to pump it into the tank. I yelled to him to shut it off. He went and got his boss, who apparently DID know how to do it. That guy asked me how it was running - he remembered the story with the rig. I told him it failed inspection again. He said "carb, right?" I said yeah. He said bring it to Steve's in Lyndhurst, which is where I had it rebuilt recently. So that's independent confirmation of Steve's good work. I just need to tune it a bit more.
A side note side note: The front calipers hung up about 5 miles into my journey. The pedal got hard and the brakes were touchy. When I stopped at a light I could smell hot brakes. I pulled into a parking lot. Couldn't see anything obvious but the front brakes smelled hot. I let it cool off and it was fine the rest of the trip. It was odd, but it worries me that it could do it again. It was the first long-ish drive after sitting all winter, though.
Annnnnd.....it's leaking something again. It's dripping off the frame by the radiator. Looks like oil - could be the trans cooler lines leaking again. My bud that bought the '87 Allegro finally got his back from the shop after 5 months. He has the same exact issues: leaking trans lines, upper rad hose leaking, fuel pump safety switch leaking oil.
Man I'm rambling this morning. I need to cut back on the coffee!!!
Well Jim, you could install a cheap universal converter.Then remove it after the e test.Dakota is right about them getting to hot for everyday driving.
Well like I said, stupid suggestion time LOL
If Im not mistaken but I thought Jims engine was a big block 454.. If it is, ya cant put a catalytic convertor on it... Will run hot and that catalytic converter will glow like a 500 watt light bulb.
Stupid suggestion time. How about installing a catalytic converter into the exhaust system. They are under $150 and even less on eBay. Would that clean up your exhaust? or do they only work with fuel injected engines? My limited knowledge is being dangerous again LOL
If you love classic and vintage RVs then come Join us. Come on in and have some fun. JOIN HERE NOW
Started by Tom Cogdell in RV Repair & Maintence May 25.
Started by Ken Vanderburg in RV Repair & Maintence May 22.
Started by Cobytogo in Vintage RV Salvage Yards & Used RV Parts Sources & Suppliers. Last reply by Cobytogo May 11.
Posted by Alfonso Vilches on July 7, 2023 at 8:18pm
Posted by Ellen (Ellie) Rice on December 9, 2022 at 6:24pm — 1 Comment
Posted by David & Misty Preciado on June 10, 2022 at 6:18pm — 2 Comments
Posted by John Curtis on March 5, 2022 at 11:00am
Added by Jimco_W001
-CLASS C FULL Frame off Restoration by Kevin Crowley
-Kerry Malseed's 1947 Flxible Clipper Bus Restoration
-Kevin's Wildcat Trailer Frame Up Restoration & Materials Used
-Rod Paints His Trailer Before/After Pics
-Understanding Brake Controllers
Blogs, Posts and Other things We like to Follow....
Vintage Travel Trailers, Vintage Campers, Camper Restoration, Bus Conversions, Vintage RV Forums, Old RVs, Tiny Homes, Boondocking
A work of art by member Paige Bridges
+++++++++++++++++++++++++++++
Disclaimer - Please Read it
Enjoy this site and use it totally at your own risk.
By using or viewing this site YOU agree to Hold Harmless anyone associated with it including other members. Also, YOU agree that YOU are solely responsible for ANY and ALL actions, results or damages. Members "opinions" are just that and any repair or alteration comments or recommendations are by folks who are not licensed repair or mechanical professionals. Any repairs or modifications you do totally at YOUR OWN RISK. Use licensed professionals for all work to avoid possible serious injury or damage. Use banks for purchases. Have fun!
Copywrite & Trade Mark Registered GoodOldRV© ,GoodOldRVs©, GoodOldRVs.com©,GoodOldRVs.net©,GoodOldRV.Com©
© 2024 Created by Jimco_W001. Powered by
You need to be a member of Good Old RVs to add comments!
Join Good Old RVs